NUOVA versione 4.080 NON BETA
  • 17 voti - 3 media
#1
Mi è appena apparsa la disponibilità della nuova versione NON BETA  4.080.
Aggiornamento da 3.601 per HCLite .
Chi fa da cavia?????? Rolleyes Cool Rolleyes

Queste le novità:

Version 4.080

This update allows migration from version 3.601, featuring reconfiguration for every device, adjusting it for changes which took place in the system. This will assure possibly smooth transition and continuous operation, allowing each device to work with old settings until reconfiguration is done. Please refer to message that appears in interface and Notification Center after finishing upgrade for further instructions.

Important!
Updating from version 3.601 may take longer than usual, up to 30 minutes, please do not restart controller during update process.

Resolved issues:
- #0002290 #0003353 Devices with sceneActivation are not available in Block and Magic scenes
- No user icons in Remote Access
- Gateway Connection - devices with polling interface are not being imported
- 503 error when including blind controller from some manufacturers
- Delays in Z-wave network after setting RGBW Controller to desired level
- #0003502 Aeon (4 in 1) Humidity Sensor - humidity now updates correctly
- Devices no longer show up as "Not configured" after controller reboot
- Values in Seismometer Mode in Motion Sensor v2.7 are now reported correctly
- Logitech Harmony plug-in behaviour is adjusted to recent changes in Logitech's API
- PTZ cameras movement can now be controlled as plug-in with mobile devices
- Drop-down lists on Firefox version 40 and above are now fully functional
- Devices with multiple endpoint are now building correctly even without templates
- #0003538 Status Off after Soft Reconfiguration
- #0003208 AEOTEC GEN 5 Siren doesn't work
- #0003557 Template misssing for Zwave.ME WIN ITEMP
- #0003560: PHI_PAN06 Relay Insert 2 * Template
- #0003629: Z-wave led don't blink
- #0003628: Can't select devices as actors into alarm actions like panic, lights on
- #0003475 Power consumption gone after sw restart
- #0003530: many problems with HRT4 ASR-ZW
- Settings page for Polylock device do not load
- There is no "controlled device" after soft reconfiguration
- Problem with authentication to cameras under IE, Safari and Chrome browsers
- Breached sensor with Arm Delay causes instant alarm after being armed
- Adding devices with mobile app no longer includes them in secure mode. Non-secure inclusion is default mode now
- Improved camera streams performance both in remote and local access
- Time from last breach is now displayed in logs underneath each sensor
- Logs are now displayed and refreshed properly
- Linked Devices Panel does not load
- Actions based on schedules are not executing
- #0003667 Scenes change type when saved. Scenes that were incorrectly changed to Lua will be brought back to block mode. They will continue to operate like before, but no change will be possible, and any save will disable given scene, requiring it to be rewritten. Scenes that were switched to Lua, but with no changes applied, will be fully functional.
- #0003690 Block scenes - set values in green fields are not displayed properly
- UBS, D/W Sensor - random incorrect reports with value 0 are being received
- Battery icon not shown in main device
- #0003730 AEON 6 in 1 - device page does not load
- #0003763 Block and Lua scenes are generated empty and require save to be edited
- Hour in Magic Scenes displayed inappropriately
- Verification of Recovery Memory status requires double click
- Magic Scenes based on time loops when triggered manually
- #0002322 #0002318 Smart Energy Switch - device lacks measured power value
- #0003735 Learning mode error - inclusion mode locks, reboot is required
- #0003745 Wall Plug icon is missing in Magic Scenes

New devices support:
- FIBARO SWIPE
- HEATIT Z-Wave Thermostat
- Evolve LDM-15
- Evolve LPM-15
- Evolve LFM-20
- Evolve LRM-AS-W
- Evolve LOM-15
- Evolve LTM-5
- Evolve LSM-15
- Evolve LRM-1000
- Philio D/W Sensor PST02-1C
- Ecolink Z-Wave Garage Door Tilt Sensor
- Linear/ GoControl WAPIRZ-1 PIR Motion Detector
- Danfoss RS Room Sensor
- FortrezZ WWA01AA
- FortrezZ WWA-02
- Philio PAN06
- Everspring SF813-2
- Z-Wave.Me ZMR WCS 6 v1.4
- Z-Wave.Me On Off Switch
- Z-Wave.Me FB10 v1.1
- Z-Wave.Me Wall Controller v1.1
- Z-Wave.Me TZ68 g v1.0
- NodOn Octan Remote v2.3
- Philio PSM02 4 in 1 Sensor v1.0
- EMINENT EM6570
- EMINENT EM6550
- TKB Home Wall Plug v1.1
- TKBHome TZ67 v1.12
- Reitz Group ZW ESJ v1.0
- Reitz Group ZS 3500 v1.0
- Reitz Group IP44 On Off Switch v1.0
- FortrezZ LLC-SSA03 v2.5
- GreenWave Powernode v4.27
- Qees Remote Controller v0.5
- Jasco Products Wall Outlet v1.16
- Jasco Products ZW3003
- Jasco Products ZW4101
- Everspring HAC01 v2.0
- BeNext-Dimmer
- BeNext-Forest Curtain rail with motor
- wiDom-Universal Power Meter v1.30
- Popp Dimmer v1.0
- Popp On Off Socket v1.0
- CBCC Sarl-Swiidinter
- Aeon Labs SES G2
- Aeon Labs Aeotec Smart Energy Power Strip (DSC11-ZWUS)
- Aeon Labs Micro Smart Energy Switch
- Aeon Labs Recessed Door Sensor
- Aeon Labs DSC26103
- Vision ZR1202 v1.74
- Vision Security ZS5101 v1.65
- Kwikset-Smart Code 916 v3.37
- Yale-T1L v18.128
- Yale Door Lock v80.32
- RTC-CT100 Thermostat v9.1
- #0003573, #0003612 - AEON MultiSensor 6
- RCS EM52-ZW
- RCS PMC40DR-ZW
- Everspring HSM02
- AEON DSB05-ZWUS
- AEON DSB28-ZWUS
- #0002435 Aeon Labs Smart Switch DSC24
- #0002306 Aeon Labs DSC06106

Other improvements:
- Due to multiple requests we introduced mechanism of limiting number of single scene instances running simultaneously. Maximum number is 10 instances active at the same time. It is available in all types of scenes. In case of exceeding given number the additional scene will not be started and proper notification will appear in Notification center. Remember, that all block and magic scenes based on time have always once instance running in loop, so if there is only single instance allowed, clicking "Run" button will have no effect.
- In case of exceeding 95% of RAM's "used space", no new scenes will be triggered until that value drops again
- Support for devices that use Central Scene (keyfobs, wall controllers etc) added
- SceneActivation interface will be added automatically if device uses this Command Class (even if device does not declare support explicitly)
- Custom handling of some power/energy reports (for third party devices)
- Improved communication with battery operated devices (unsuccessfully sent commands won't be dropped)
- Improved Z-Wave engine stability
- Notification about exceeding RAM limit (95%) by scene will no longer be duplicated
- Block and Magic scenes triggered by some value that persists for given time are now aborted immediately if condition is not met
- Default number of instances in all kinds of scenes is set to 2
- Notifications received from Dimmer 2 (regarding issues like overload, voltage drop etc) are now displayed in log window (located on the top of main page)
- Improved stability
- PIN dfor new user is now set to '1111' by default
- In case of empty user PIN, it is set to default value - '1111'
- Improved stability
- Minor UX fixes
- filters in /api/devices that allows for filtering out devices that meet some requirements, examples:

HC IP/api/devices?visible=true returns devices with visible equal to 'true'
HC IP/api/devices?property=[batteryLevel,100] returns devices with property batteryLevel equal to 100
HC IP/api/devices?interface=light returns devices with light interface

Multiple filters can be used together, for example: HC IP/api/devices?visible=true&interface=light returns devices with visible equal to 'true' and with 'light' interface
Questo messaggio è stato modificato l'ultima volta il: 04-03-2016, 08:06 AM da kead.
#2
http://forum.fibaro.com/index.php?/topic...-hcl-4080/ ---- attendiamo feedback
#3
Io ho aggiornato su HC2 senza problemi.
Al momento mi sembra stabile.
Fibaro HC2 + HClite+ Satel Integra 32 + Nas Synology 415plus + Nabaztag V2
#4
Aggiornato ora. Tutto ok da 4.070 a 4.080 circa 10 minuti.
#5
Notare il fix sulle solite icone dal sito remote  Big Grin vediamo se al prossimo aggiornamento le rompono di nuovo  Tongue
Baran
-MasterOfDisasters-
Fibaro HC2 | ProLiant Micro | Zentyal | Foscam IpCam | Rocki | Denon AVR-X2
#6
Ciao a tutti, chi ha provato ad aggiornare HCL con il nuovo firmware?


Inviato dal mio iPhone utilizzando Tapatalk
#7
Ci ho provato io  e ovviamente ora NON FUNZIONA PIù NIENTE. 
Sto provando a saltarci fuori dalle 17 , ma proprio niente E' tutto completamente diverso ed adesso temo CHE MI ASPETTERA' UNA NOTTATA AL FREDDO.  Infatti il termostato non comanda più niente .... 

Si accettano suggerimenti, possibilmente semplici, ma va bene tutto sigh sigh
#8
Provo a farvi domande specifiche, partendo da quelle più urgenti. 
Tutti e dico tutti i dispositivi sono diventati SLAVE  di un non meglio identificato MASTER Main_Zwave_Device (che risulta non assegnato). E' normale? che vuol dire e cosa comporta? 

ILPIù URGENTE
Mi ha bloccato il termostato SECURE SRT321. Non c'è stato verso di ripristinarlo correttamente dal sistema di riconfigurazione soffice che sta cavolo di versione propone. Alla fine l'ho cancellato (non senza difficoltà) e l'ho ri inserito (con ancora maggiori difficoltà) La nuova versione non lo riconosce più come marca e modello e non gli assegna l'icona (non me ne fa assegnare nessuna). SOPRATUTTO non riesco a collegarlo all'interruttore della Widom (che sembra a posto) che farebbe partire effettivamente la caldaia. 

Qualcuno mi potrebbe aiutare almeno su questo ?

PS ovviamente non mi fa tornare alla versione precedente. In backup fatto prima dell'aggiornamento c'è ma la funzione di ripristino è disabilitata
Questo messaggio è stato modificato l'ultima volta il: 05-03-2016, 08:24 AM da giesgi.
#9
Da come la descrivi sembra che ci sia stato un errore in fase di upgrade.
Non riesci a togliere e riassociare i dispositivi di tuo interesse?
Down grande ad altra versione precedente?
Hai fatto reboot in modo brutale (togli e alimentazione e riavvia)?
Fibaro HC2 + HClite+ Satel Integra 32 + Nas Synology 415plus + Nabaztag V2
#10
Se non ti legge il secure la soluzione è provvisoriamente di fare un programmatore orario che comandi il widom (se usi il pannello irrigazione è comodo)


Utente(i) che stanno guardando questa discussione:
1 Ospite(i)